DPF 8000™ Ultra Tack

Industrial Grade Multi-Purpose Calendered Film for Hard-to-Stick Surfaces

DPF 8000™ Ultra Tack is a 3.5-mil (90 micron) satin white, high-tensile, PVC film with aggressive, permanent pressure-sensitive adhesive. Designed to adhere to “hard-to-stick” surfaces, DPF 8000™ Ultra Tack offers a special adhesive system that is designed to adhere to difficult substrates and low surface energy plastics, especially ABS plastic. DPF 8000™ White is also designed to meet typical permanent marking requirements and specifications for heavy industrial equipment markings, including OEM markings, off-road vehicles such as motorbikes, and other hard-to-stick applications. The film installs best on flat surfaces when processed and applied according to Arlon recommendations. DPF 8000™ Ultra Tack is fire certified under ASTM E-84 and EN 13501-1:2007+A1:2009 of Euro Class C, S1, d0. This product is also rated up to 7 years* (unprinted) for outdoor durability. Printed durability is dependent on the ink system used.

Applications & Features

  • Digital printing with a wide variety of direct print systems.
  • Polyolefin plastic surfaces such as polyethylene, polypropylene, polyurethane, etc.
  • Application in cold temperature environments.
  • Slightly textured and/or low-energy surfaces.
Certified for HP Latex Inks

Performance & Physical Data

Property Test Methods Typical Value
Surface Finish Gloss Meter 60° Reflection 40 to 60 Gloss Units
Thickness Micrometer, Federal Bench Type 3.5-mil (90 micron)
Tensile Strength Tensile Tester with 2-in (51 mm) jaw separation; crosshead speed of 12 in/min. (5.1 mm/s), web direction 13.0 lb/in 2.3 kg/cm
Elongation Instron Tensile Tester as above > 150%
Shelf Life (In Box) Ideal Storage Temperature 70°F (21°C) and 50% relative humidity 1 year from factory shipment
Application Temperature Range On clean, dry substrate 30°F to 80°F optimum -1°C to 27°C optimum
Service Temperature Range On clean, dry substrate -65°F to 225°F -54°C to 107°C
Dimensional Stability 158°F (70°C), 48 hours 50 - 150 mil 1..27 - 3.81 mm
Peel Adhesion PSTC-1, 15 min, 70°F (21°C) 5.0 lb/in 0.89 kg/cm
Liner Release TLMI Release at 90˚, 300 in/min (760 cm/min) 50 g/2 in 9.8 g/cm
* Outdoor durability for vertical masonry surfaces rated up to 6 months and up to 1 year for vertical exposure on flat surfaces. This is contingent upon no rain or harsh outdoor weather conditions. + Arlon does not warranty DPF 8000™ for floor graphics.

Preparation & Installation

General

DPF 8000 Ultra Tack owes its very high bond to the softness of the adhesive. The trade off for high tack and adhesion is
to expect higher visible shrinkage than normal. As a result, it is best practice to not leave the printer unattended when printing to avoid headstrikes due to adhesive build up on the film edges over time. Click here to see the WrapItRight video: Preventing Adhesive Build-Up When Printing with Arlon DPF 8000™. When decorating DPF 8000™ White with screen or digital printing the solvent involved will penetrate both the vinyl and adhesive at the time of printing. If the printing solvents aren’t completely removed before installation the resultant graphic will show very high shrinkage and edge curl. When printing this product be vigilant about drying the finished decal completely before laminating, top coating or installing.

Concrete, Masonry and Tile

The surface should be entirely dust free: high pressure TSP/water wash is the easiest method. The surface must be sealed with a complete coat of paint or concrete sealer and allowed to dry. If the surface is not sealed there must be no loose paint, grit or chalk present.

Sealing porous surfaces creates three benefits:

Moisture cannot wick to the adhesive surface from within the matrix of the wall.

Dust due to ablation cannot develop under the vinyl.

Removal steps are much easier as the adhesive will remove more cleanly and if any adhesive remains, the surface will be cleaned of residue more easily.

The surface temperature must be above 50°F (10°C). To assure highest adhesion the graphics will benefit from a final installation pass using a soft roller and heat source in combination. The film should be heated to a point of softening. Wait until the vinyl becomes “tack-free” and then roll the film tightly into the texture of the wall.

Plastic

These surfaces benefit from slightly roughening with sand paper before installation or surface oxidation with flame. For many polyolefinic surfaces, once the oily skin of the plastic is modified bond will improve dramatically.

Addition of heat during removal will make the process much cleaner and faster. Where possible allow the surface to reach 80°F/27°C or more before removing the film. Where ambient temperature is not that high use either a very “soft” flame type torch or heat gun to bring the temperature up. Arlon recommends getting the film and under laying adhesive above 100°F/38°C.

Due to the porosity of certain types of plastics (i.e. PP, PE), plastics exposed to gasoline from tanks will migrate through plastic and interfere with vinyl adhesion to the plastic. We do not recommend wrapping gasoline tanks or similar plastics exposed to like fumes.

Graphics Removal

Remove the film in a continuous smooth motion at a shallow angle for the fastest separation. Where it is practical, two people on the removal make the job go far faster than using just one. With one person working the heating unit in front of the second person who is peeling film, the job proceeds at a uniform and consistent pace. Where only one person is working there will be constant starting and stopping in addition to the problems of the heat being very inconsistent.

Removal Recommendations

Temp range 55°F (13°C) or higher. If environment temperature is lower than 55°F (13°C), heat gun or blow torch should be used.

Film removal angle >90 degrees from vertical wall.

Removal rate: slow (1 in/sec) and constant pull of graphics towards the ground.

Special Considerations

Because of the porous nature of all masonry and its general roughness Arlon does expect water, snow or ice to seep between the film and wall and collect on the upper edges of the applied graphic. For this reason an edge seal is recommended on applications that have very rough surfaces. Rough surfaces may not carry the standard warranties.

Standard warranty applies to vertical applications only. Vertical is defined as +/- 10° from the vertical. Non-vertical applications are not warranted for this product.